- 556 -
pin 1 pin 2 case positive case GPAF1601 thru gpaf1607 isolation 16.0 amps. glass passivated rectifiers voltage range 50 to 1000 volts current 16.0 amperes f eatures low forward voltage drop high current capability high reliability high surge current capability m echanical data cases: ito-220ac molded plastic epoxy: ul 94v-0 rate flame retardant terminals: leads solderable per mil-std- 202, method 208 guaranteed polarity: as marked high temperature soldering guaranteed: 260 / 0.25? (6.35mm) from case 10 seconds. mounting torque: 5 in ? 1bs. max. weight: 2.24 grams ito-220ac dimensions in inches and (millimeters) m aximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol gpaf 1601 gpaf 1602 gpaf 1603 gpaf 1604 gpaf 1605 gpaf 1606 gpaf 1607 uni ts maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current .375?(9.5mm) lead length @t c = 100 i (av) 16.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 250 a maximum instantaneous forward voltage @16.0a v f 1.1 v maximum dc reverse current @ t c =25 at rated dc blocking voltage @ t c =125 i r 10 250 ua ua typical junction capacitance ( note 1 ) cj 100 pf typical thermal resistance (note 2) r jc 4.0 / w operating and storage temperature range t j ,t stg - 65 to + 150 notes: 1. measured at 1 mhz and app lied reverse voltage of 4.0 volts d.c. 2. thermal resistance from junction to case mounted on heatsink size 2? x 3? x 0.25 ? al-plate
- 557 - ratings and characteristic curves (GPAF1601 thru gpaf1607) fig.2- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 5 10 20 100 50 50 0 200 150 100 250 300 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.3- typical instantaneous forward characteristics instantaneous for ward current . (a) 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.4 0.2 1 4 2 10 20 40 100 200 400 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o fig.4- typical reverse characteristics 0 20 40 60 80 100 120 140 0.1 0.4 0.2 1 4 40 2 10 100 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 fig.5- typical junction capacitance junction cap acitance.(pf) 1 0 5 10 50 100 1000 500 20 40 60 100 80 120 reverse voltage. (v) tj=25 c 0 fig.1- maximum forward current derating curve average for ward current . (a) 0 50 100 150 8 10 12 14 16 18 case temperature. ( c) o single phase half wave 60hz resistive or inductive load instantaneous reverse current .( a)
|